OBJECT = COLUMN
NAME = "SCET_UTC"
DATA_TYPE = TIME
UNIT = "N/A"
START_BYTE = 1
BYTES = 19
FORMAT = "A19"
DESCRIPTION = "
The UTC spacecraft event time (SCET) determined from the packet's SCLK
value. The time format is yyyy-mm-ddThr:mn:sc.
"
END_OBJECT = COLUMN
OBJECT = COLUMN
NAME = "STATE_INDEX"
DATA_TYPE = ASCII_INTEGER
UNIT = "N/A"
START_BYTE = 20
BYTES = 5
FORMAT = "I5"
VALID_MAXIMUM = 9999
DESCRIPTION = "
The state index is a counter that starts at 0 and increments every
time the state changes.
"
END_OBJECT = COLUMN
OBJECT = COLUMN
NAME = "DELTA_SCLK"
DATA_TYPE = ASCII_INTEGER
UNIT = "SECONDS"
START_BYTE = 25
BYTES = 8
FORMAT = "I8"
VALID_MAXIMUM = 9999
MISSING_CONSTANT = -999
DESCRIPTION = "
The number of SCLK ticks (seconds) that the instrument was in the
state. When only one state is present, then the duration is unknown.
The last state for a file with multiple states has an unknown
duration. These states are assigned the MISSING_CONSTANT.
"
END_OBJECT = COLUMN
OBJECT = COLUMN
NAME = "SCLK"
DATA_TYPE = ASCII_INTEGER
UNIT = "SECONDS"
START_BYTE = 33
BYTES = 11
FORMAT = "I11"
VALID_MAXIMUM = 4294967295
DESCRIPTION = "
Spacecraft clock count at the start of the SOH interval.
"
END_OBJECT = COLUMN
OBJECT = COLUMN
NAME = "TELREADOUT"
DATA_TYPE = ASCII_INTEGER
UNIT = "SECONDS"
START_BYTE = 44
BYTES = 6
FORMAT = "I6"
VALID_MINIMUM = 15
VALID_MAXIMUM = 2000
DESCRIPTION = "
Measurement interval for the science data.
"
END_OBJECT = COLUMN
OBJECT = COLUMN
NAME = "TELSOH"
DATA_TYPE = ASCII_INTEGER
UNIT = "SECONDS"
START_BYTE = 50
BYTES = 6
FORMAT = "I6"
VALID_MINIMUM = 2
VALID_MAXIMUM = 2000
DESCRIPTION = "
Measurement interval for the state-of-health readout.
"
END_OBJECT = COLUMN
OBJECT = COLUMN
NAME = "MODE"
DATA_TYPE = ASCII_INTEGER
UNIT = "N/A"
START_BYTE = 56
BYTES = 2
FORMAT = "I2"
DESCRIPTION = "
Instrument mode (0=Standby, 1=Normal, 2=Anneal)
"
END_OBJECT = COLUMN
OBJECT = COLUMN
NAME = "HVPS1_SET"
DATA_TYPE = ASCII_REAL
UNIT = "VOLTS"
START_BYTE = 58
BYTES = 9
FORMAT = "F9.2"
DESCRIPTION = "
Set point for high voltage power supply (HVPS) 1, which supplies the
photomultiplier tube for the +Z phoswich.
"
END_OBJECT = COLUMN
OBJECT = COLUMN
NAME = "HVPS1"
DATA_TYPE = ASCII_INTEGER
UNIT = "N/A"
START_BYTE = 67
BYTES = 2
FORMAT = "I2"
VALID_MAXIMUM = 1
DESCRIPTION = "
If 1, then HVPS1 is enabled.
"
END_OBJECT = COLUMN
OBJECT = COLUMN
NAME = "HVPS2_SET"
DATA_TYPE = ASCII_REAL
UNIT = "VOLTS"
START_BYTE = 69
BYTES = 9
FORMAT = "F9.2"
DESCRIPTION = "
Set point for high voltage power supply (HVPS) 2, which supplies the
photomultiplier tube for the -Z phoswich.
"
END_OBJECT = COLUMN
OBJECT = COLUMN
NAME = "HVPS2"
DATA_TYPE = ASCII_INTEGER
UNIT = "N/A"
START_BYTE = 78
BYTES = 2
FORMAT = "I2"
VALID_MAXIMUM = 1
DESCRIPTION = "
If 1, then HVPS2 is enabled.
"
END_OBJECT = COLUMN
OBJECT = COLUMN
NAME = "HVPS3_SET"
DATA_TYPE = ASCII_REAL
UNIT = "VOLTS"
START_BYTE = 80
BYTES = 9
FORMAT = "F9.2"
DESCRIPTION = "
Set point for high voltage power supply (HVPS) 3, which supplies the
photomultiplier tube for the -Y boron-loaded plastic scintillator.
"
END_OBJECT = COLUMN
OBJECT = COLUMN
NAME = "HVPS3"
DATA_TYPE = ASCII_INTEGER
UNIT = "N/A"
START_BYTE = 89
BYTES = 2
FORMAT = "I2"
VALID_MAXIMUM = 1
DESCRIPTION = "
If 1, then HVPS3 is enabled.
"
END_OBJECT = COLUMN
OBJECT = COLUMN
NAME = "HVPS4_SET"
DATA_TYPE = ASCII_REAL
UNIT = "VOLTS"
START_BYTE = 91
BYTES = 9
FORMAT = "F9.2"
DESCRIPTION = "
Set point for high voltage power supply (HVPS) 4, which supplies the
photomultiplier tube for the +Y boron-loaded plastic scintillator.
"
END_OBJECT = COLUMN
OBJECT = COLUMN
NAME = "HVPS4"
DATA_TYPE = ASCII_INTEGER
UNIT = "N/A"
START_BYTE = 100
BYTES = 2
FORMAT = "I2"
VALID_MAXIMUM = 1
DESCRIPTION = "
If 1, then HVPS4 is enabled.
"
END_OBJECT = COLUMN
OBJECT = COLUMN
NAME = "HVPS5_SET"
DATA_TYPE = ASCII_REAL
UNIT = "VOLTS"
START_BYTE = 102
BYTES = 9
FORMAT = "F9.2"
DESCRIPTION = "
Set point for high voltage power supply (HVPS) 5, which supplies the
photomultiplier tube for the BGO scintillator.
"
END_OBJECT = COLUMN
OBJECT = COLUMN
NAME = "HVPS5"
DATA_TYPE = ASCII_INTEGER
UNIT = "N/A"
START_BYTE = 111
BYTES = 2
FORMAT = "I2"
VALID_MAXIMUM = 1
DESCRIPTION = "
If 1, then HVPS5 is enabled.
"
END_OBJECT = COLUMN
OBJECT = COLUMN
NAME = "HVPS6_SET"
DATA_TYPE = ASCII_REAL
UNIT = "VOLTS"
START_BYTE = 113
BYTES = 9
FORMAT = "F9.2"
DESCRIPTION = "
Set point for high voltage power supply (HVPS) 6, which provides the bulk
bias for the CZT array.
"
END_OBJECT = COLUMN
OBJECT = COLUMN
NAME = "HVPS6"
DATA_TYPE = ASCII_INTEGER
UNIT = "N/A"
START_BYTE = 122
BYTES = 2
FORMAT = "I2"
VALID_MAXIMUM = 1
DESCRIPTION = "
If 1, then HVPS6 is enabled.
"
END_OBJECT = COLUMN
OBJECT = COLUMN
NAME = "PM5_LVPS"
DATA_TYPE = ASCII_INTEGER
UNIT = "N/A"
START_BYTE = 124
BYTES = 2
FORMAT = "I2"
VALID_MAXIMUM = 1
DESCRIPTION = "
If 1, the analog +/-5V low voltage power supply is enabled. The supply
provides power for analog and digital components, including the
scintillator pulse processing electronics and internal sensors
(temperature and voltage).
"
END_OBJECT = COLUMN
OBJECT = COLUMN
NAME = "P12_LVPS"
DATA_TYPE = ASCII_INTEGER
UNIT = "N/A"
START_BYTE = 126
BYTES = 2
FORMAT = "I2"
VALID_MAXIMUM = 1
DESCRIPTION = "
If 1, the +12V low power supply is enabled, which supplies the high
voltage power supplies (if MODE=1) and the resistive heaters (if MODE=2)
used to anneal the CZT array.
"
END_OBJECT = COLUMN
OBJECT = COLUMN
NAME = "CZT_PM5_LVPS"
DATA_TYPE = ASCII_INTEGER
UNIT = "N/A"
START_BYTE = 128
BYTES = 2
FORMAT = "I2"
VALID_MAXIMUM = 1
DESCRIPTION = "
If 1, the +/-5V supply for the CZT analog pulse processing circuits
is enabled.
"
END_OBJECT = COLUMN
OBJECT = COLUMN
NAME = "CZT_ENABLES"
DATA_TYPE = CHARACTER
UNIT = "N/A"
START_BYTE = 130
BYTES = 17
FORMAT = "A17"
DESCRIPTION = "
Bit pattern indicating the state (1=disabled, 0=enabled) of each of the
16 CZT sensors, represented as a character string. For readability,
the first character is blank. The remaining characters represent bits,
read right to left, which give the state of the 16 sensors in order from
0-15. For example, the pattern 1111111111111110 indicates that all of
the CZT sensors are disabled except for sensor 0. The pattern
0010000000000010 indicates that two of the sensors (1 and 13) are
disabled.
"
END_OBJECT = COLUMN
OBJECT = COLUMN
NAME = "NEMG_TOT_EVTS"
DATA_TYPE = ASCII_INTEGER
UNIT = "N/A"
START_BYTE = 147
BYTES = 5
FORMAT = "I5"
VALID_MAXIMUM = 6676
DESCRIPTION = "
Total number of gamma ray events recorded in the science data file. Note
that NEMG_TOT_EVTS + NEMN_TOT_EVTS is always less than or equal to
6676.
"
END_OBJECT = COLUMN
OBJECT = COLUMN
NAME = "NEMG_CZT_EVTS"
DATA_TYPE = ASCII_INTEGER
UNIT = "N/A"
START_BYTE = 152
BYTES = 5
FORMAT = "I5"
VALID_MAXIMUM = 6676
DESCRIPTION = "
The number of CZT single interaction (CAT10) events recorded in the
event buffer. This value is always less than NEMG_TOT_EVTS.
"
END_OBJECT = COLUMN
OBJECT = COLUMN
NAME = "NEMN_TOT_EVTS"
DATA_TYPE = ASCII_INTEGER
UNIT = "N/A"
START_BYTE = 157
BYTES = 5
FORMAT = "I5"
VALID_MAXIMUM = 6676
DESCRIPTION = "
Total number of neutron events recorded in the science data file. Note
that NEMG_TOT_EVTS + NEMN_TOT_EVTS is always less than or equal to
6676.
"
END_OBJECT = COLUMN
OBJECT = COLUMN
NAME = "L_BGO_CW"
DATA_TYPE = ASCII_INTEGER
UNIT = "N/A"
START_BYTE = 162
BYTES = 5
FORMAT = "I5"
VALID_MINIMUM = 0
VALID_MAXIMUM = 1023
DESCRIPTION = "
Lower channel (output of the BGO ADC)for the CAT2 coincidence window
for the BGO sensor.
"
END_OBJECT = COLUMN
OBJECT = COLUMN
NAME = "H_BGO_CW"
DATA_TYPE = ASCII_INTEGER
UNIT = "N/A"
START_BYTE = 167
BYTES = 5
FORMAT = "I5"
VALID_MINIMUM = 0
VALID_MAXIMUM = 1023
DESCRIPTION = "
Upper channel (output of the BGO ADC)for the CAT2 coincidence window
for the BGO sensor.
"
END_OBJECT = COLUMN
OBJECT = COLUMN
NAME = "L_BGO_ROI"
DATA_TYPE = ASCII_INTEGER
UNIT = "N/A"
START_BYTE = 172
BYTES = 5
FORMAT = "I5"
VALID_MINIMUM = 0
VALID_MAXIMUM = 1023
DESCRIPTION = "
Lower channel (output of the BGO ADC)for the CAT2 region of interest
(ROI) for the BGO spectrum. Note that H_BGO_ROI - L_BGO_ROI = 64.
The window gives range of channels for the CAT2 BGO pulse height spectra.
"
END_OBJECT = COLUMN
OBJECT = COLUMN
NAME = "H_BGO_ROI"
DATA_TYPE = ASCII_INTEGER
UNIT = "N/A"
START_BYTE = 177
BYTES = 5
FORMAT = "I5"
VALID_MINIMUM = 0
VALID_MAXIMUM = 1023
DESCRIPTION = "
Upper channel (output of the BGO ADC)for the CAT2 region of interest
(ROI) for the BGO spectrum. Note that H_BGO_ROI - L_BGO_ROI = 64.
The window gives range of channels for the CAT2 BGO pulse height spectra.
"
END_OBJECT = COLUMN
OBJECT = COLUMN
NAME = "L_BLP_MY_CW"
DATA_TYPE = ASCII_INTEGER
UNIT = "N/A"
START_BYTE = 182
BYTES = 4
FORMAT = "I4"
VALID_MINIMUM = 0
VALID_MAXIMUM = 255
DESCRIPTION = "
Lower channel (output of the BLP ADC)for the CAT2 coincidence window
for the -Y BLP sensor.
"
END_OBJECT = COLUMN
OBJECT = COLUMN
NAME = "H_BLP_MY_CW"
DATA_TYPE = ASCII_INTEGER
UNIT = "N/A"
START_BYTE = 186
BYTES = 4
FORMAT = "I4"
VALID_MINIMUM = 0
VALID_MAXIMUM = 255
DESCRIPTION = "
Upper channel (output of the BLP ADC)for the CAT2 coincidence window
for the -Y BLP sensor.
"
END_OBJECT = COLUMN
OBJECT = COLUMN
NAME = "L_BLP_MY_ROI"
DATA_TYPE = ASCII_INTEGER
UNIT = "N/A"
START_BYTE = 190
BYTES = 4
FORMAT = "I4"
VALID_MINIMUM = 0
VALID_MAXIMUM = 255
DESCRIPTION = "
Lower channel (output of the BLP ADC)for the CAT2 region of interest
(ROI) for BLP -Y. Note that H_BLP_MY_ROI - L_BLP_MY_ROI = 64. The window
gives the range of channels for the CAT2 BLP -Y pulse height spectra.
"
END_OBJECT = COLUMN
OBJECT = COLUMN
NAME = "H_BLP_MY_ROI"
DATA_TYPE = ASCII_INTEGER
UNIT = "N/A"
START_BYTE = 194
BYTES = 4
FORMAT = "I4"
VALID_MINIMUM = 0
VALID_MAXIMUM = 255
DESCRIPTION = "
Upper channel (output of the BGO ADC)for the CAT2 region of interest
(ROI) for BLP -Y. Note that H_BLP_MY_ROI - L_BLP_MY_ROI = 64. The window
gives range of channels for the CAT2 BLP -Y pulse height spectra.
"
END_OBJECT = COLUMN
OBJECT = COLUMN
NAME = "L_BLP_PY_CW"
DATA_TYPE = ASCII_INTEGER
UNIT = "N/A"
START_BYTE = 198
BYTES = 4
FORMAT = "I4"
VALID_MINIMUM = 0
VALID_MAXIMUM = 255
DESCRIPTION = "
Lower channel (output of the BLP ADC)for the CAT2 coincidence window
for the +Y BLP sensor.
"
END_OBJECT = COLUMN
OBJECT = COLUMN
NAME = "H_BLP_PY_CW"
DATA_TYPE = ASCII_INTEGER
UNIT = "N/A"
START_BYTE = 202
BYTES = 4
FORMAT = "I4"
VALID_MINIMUM = 0
VALID_MAXIMUM = 255
DESCRIPTION = "
Upper channel (output of the BLP ADC)for the CAT2 coincidence window
for the +Y BLP sensor.
"
END_OBJECT = COLUMN
OBJECT = COLUMN
NAME = "L_BLP_PY_ROI"
DATA_TYPE = ASCII_INTEGER
UNIT = "N/A"
START_BYTE = 206
BYTES = 4
FORMAT = "I4"
VALID_MINIMUM = 0
VALID_MAXIMUM = 255
DESCRIPTION = "
Lower channel (output of the BLP ADC)for the CAT2 region of interest
(ROI) for BLP +Y. Note that H_BLP_PY_ROI - L_BLP_PY_ROI = 64. The window
gives the range of channels for the CAT2 BLP +Y pulse height spectra.
"
END_OBJECT = COLUMN
OBJECT = COLUMN
NAME = "H_BLP_PY_ROI"
DATA_TYPE = ASCII_INTEGER
UNIT = "N/A"
START_BYTE = 210
BYTES = 4
FORMAT = "I4"
VALID_MINIMUM = 0
VALID_MAXIMUM = 255
DESCRIPTION = "
Upper channel (output of the BGO ADC)for the CAT2 region of interest
(ROI) for BLP +Y. Note that H_BLP_PY_ROI - L_BLP_PY_ROI = 64. The window
gives range of channels for the CAT2 BLP +Y pulse height spectra.
"
END_OBJECT = COLUMN
OBJECT = COLUMN
NAME = "L_BLP_MZ_CW"
DATA_TYPE = ASCII_INTEGER
UNIT = "N/A"
START_BYTE = 214
BYTES = 4
FORMAT = "I4"
VALID_MINIMUM = 0
VALID_MAXIMUM = 255
DESCRIPTION = "
Lower channel (output of the BLP ADC)for the CAT2 coincidence window
for the -Z BLP sensor.
"
END_OBJECT = COLUMN
OBJECT = COLUMN
NAME = "H_BLP_MZ_CW"
DATA_TYPE = ASCII_INTEGER
UNIT = "N/A"
START_BYTE = 218
BYTES = 4
FORMAT = "I4"
VALID_MINIMUM = 0
VALID_MAXIMUM = 255
DESCRIPTION = "
Upper channel (output of the BLP ADC)for the CAT2 coincidence window
for the -Z BLP sensor.
"
END_OBJECT = COLUMN
OBJECT = COLUMN
NAME = "L_BLP_MZ_ROI"
DATA_TYPE = ASCII_INTEGER
UNIT = "N/A"
START_BYTE = 222
BYTES = 4
FORMAT = "I4"
VALID_MINIMUM = 0
VALID_MAXIMUM = 255
DESCRIPTION = "
Lower channel (output of the BLP ADC)for the CAT2 region of interest
(ROI) for BLP -Z. Note that H_BLP_MZ_ROI - L_BLP_MZ_ROI = 64. The window
gives the range of channels for the CAT2 BLP -Z pulse height spectra.
"
END_OBJECT = COLUMN
OBJECT = COLUMN
NAME = "H_BLP_MZ_ROI"
DATA_TYPE = ASCII_INTEGER
UNIT = "N/A"
START_BYTE = 226
BYTES = 4
FORMAT = "I4"
VALID_MINIMUM = 0
VALID_MAXIMUM = 255
DESCRIPTION = "
Upper channel (output of the BGO ADC)for the CAT2 region of interest
(ROI) for BLP -Z. Note that H_BLP_MZ_ROI - L_BLP_MZ_ROI = 64. The window
gives range of channels for the CAT2 BLP -Z pulse height spectra.
"
END_OBJECT = COLUMN
OBJECT = COLUMN
NAME = "L_BLP_PZ_CW"
DATA_TYPE = ASCII_INTEGER
UNIT = "N/A"
START_BYTE = 230
BYTES = 4
FORMAT = "I4"
VALID_MINIMUM = 0
VALID_MAXIMUM = 255
DESCRIPTION = "
Lower channel (output of the BLP ADC)for the CAT2 coincidence window
for the +Z BLP sensor.
"
END_OBJECT = COLUMN
OBJECT = COLUMN
NAME = "H_BLP_PZ_CW"
DATA_TYPE = ASCII_INTEGER
UNIT = "N/A"
START_BYTE = 234
BYTES = 4
FORMAT = "I4"
VALID_MINIMUM = 0
VALID_MAXIMUM = 255
DESCRIPTION = "
Upper channel (output of the BLP ADC)for the CAT2 coincidence window
for the +Z BLP sensor.
"
END_OBJECT = COLUMN
OBJECT = COLUMN
NAME = "L_BLP_PZ_ROI"
DATA_TYPE = ASCII_INTEGER
UNIT = "N/A"
START_BYTE = 238
BYTES = 4
FORMAT = "I4"
VALID_MINIMUM = 0
VALID_MAXIMUM = 255
DESCRIPTION = "
Lower channel (output of the BLP ADC)for the CAT2 region of interest
(ROI) for BLP +Z. Note that H_BLP_PZ_ROI - L_BLP_PZ_ROI = 64. The window
gives the range of channels for the CAT2 BLP +Z pulse height spectra.
"
END_OBJECT = COLUMN
OBJECT = COLUMN
NAME = "H_BLP_PZ_ROI"
DATA_TYPE = ASCII_INTEGER
UNIT = "N/A"
START_BYTE = 242
BYTES = 4
FORMAT = "I4"
VALID_MINIMUM = 0
VALID_MAXIMUM = 255
DESCRIPTION = "
Upper channel (output of the BGO ADC)for the CAT2 region of interest
(ROI) for BLP +Z. Note that H_BLP_PZ_ROI - L_BLP_PZ_ROI = 64. The window
gives range of channels for the CAT2 BLP +Z pulse height spectra.
"
END_OBJECT = COLUMN